5-Star · Open Mon–Sat 8 AM–7 PM

(719) 960-7208
All Posts

Heat Pump Defrost Cycle: What's Normal and What Isn't

November 18, 2026

Heat Pump Defrost Cycle: What's Normal and What Isn't

Steam rising as a heat pump defrosts

A heat pump goes into defrost mode to melt frost off its outdoor coil, and it does so by briefly running in reverse for roughly 5 to 15 minutes before returning to heating. During that window you may see steam, hear a whoosh, feel cooler air at the vents, or see AUX on the thermostat. All of that is usually normal. What is not normal is ice that keeps growing, defrost that never ends, or a unit that cycles in and out of defrost over and over. This guide explains the difference so you know when to relax and when to call.

Strongheatingandcooling
Get Help With Heat Pump Issues
Strong Heating And Cooling provides HVAC repair in Colorado Springs, with NATE-certified technicians serving residential and commercial customers.
Visit

TL;DR

  • Defrost mode melts frost from the outdoor coil by reversing refrigerant flow for a few minutes, then the system returns to heating.
  • Steam, a stopped outdoor fan, a swooshing sound and a brief burst of cooler air or AUX heat on the thermostat are typical during defrost.
  • Most cycles run about 5 to 15 minutes, and a unit checks for defrost every 30 to 90 minutes in cold, damp weather.
  • Ice that keeps thickening, defrost that drags on, or heat that never returns points to a sensor, control board, airflow or refrigerant problem that needs a technician.
  • Keep the unit clear of snow and debris, and never chip ice off the coil.

Table of Contents

What the defrost cycle is and why it exists

A heat pump heats your home by pulling heat out of the outdoor air, even when that air is cold. To do that, the outdoor coil has to run colder than the air around it. Trane explains that the coil is typically 10 to 20°F colder than the outdoor air, so it collects moisture the way a glass of ice water does on a summer day. When the temperature is low enough, that moisture freezes and begins to block airflow across the coil.

A coil buried in frost cannot absorb heat well, so the system needs a way to clear it. The defrost cycle does that. The reversing valve redirects refrigerant so the heat pump briefly operates in its cooling mode, which sends warm refrigerant to the outdoor coil and melts the ice. Once the coil is clear, the valve switches back and heating resumes.

So defrost is not a malfunction. It is a built-in part of how a heat pump works through winter, much like a furnace cycling on and off. The question is never whether your system defrosts, but whether it does so on a normal schedule and finishes the job.

Why frost forms even above freezing

Many homeowners are surprised to see frost on the unit when the thermometer reads 38 or 40°F. Because the coil runs colder than the air, it can sit below 32°F while the outdoor temperature is still above freezing. Trane notes that periodic frost is expected for exactly this reason, and its defrost guide says defrost can start in the low 40s°F, though it is more common in the 20s or 30s.

Damp air makes it worse. Rheem’s owner’s manual says that frost may begin to form when the outdoor temperature falls below 45°F and is heaviest on damp days around 35 to 40°F. A cold, dry day at 15°F often produces less frost than a humid, foggy morning just under freezing.

That matters on the Front Range, where a snowstorm can be followed by a sunny afternoon in the 40s and a freezing night. Melting snow adds moisture around the unit, and refreezing overnight adds to the load on the defrost system. Our heat pump work in Colorado Springs is built around those swings in temperature.

What you will see, hear and feel during defrost

Once you know what the cycle looks like, it stops being alarming. Here is what Trane and Rheem describe.

Outside, the fan stops and you may see a cloud of steam rising from the unit. Trane says that steam is simply ice melting and evaporating and is perfectly normal. You may also hear a swoosh or hiss as refrigerant changes direction. Rheem’s instructions add that the compressor and fan pause, the compressor restarts after about 30 seconds to heat the coil, and after defrost the fan restarts, the compressor pauses about 30 seconds, then normal heating resumes.

Inside, the thermostat may show AUX or AUX heat, and the air from the vents can feel cooler for a few minutes. Many systems turn on backup electric heat during defrost so the house does not feel the temperature dip. If your system has it, the warm-up may be barely noticeable. If not, the air can feel lukewarm until the cycle ends.

The sights and sounds are also different from house to house, because manufacturers use different controls. If you want to know what is normal for your system in particular, the model number on the outdoor unit tells a technician exactly how it is set up.

How long defrost lasts and how often it runs

A typical defrost runs about 5 to 15 minutes, and in cold, humid weather a heat pump may defrost every 30 to 90 minutes. The exact numbers depend on the controls.

Most systems decide when to defrost using a combination of time and temperature. Daikin’s service instructions for one residential line describe how it works: a sensor reads the outdoor coil temperature, and when it is low enough (about 31°F) the control board starts adding up compressor run time. When that total reaches a selectable interval of 30, 60, 90 or 120 minutes and the thermostat is calling for heat, defrost starts. It ends when the coil warms to about 75°F or after a maximum of 10 minutes, whichever comes first.

Other manufacturers use different numbers. The home-inspector group NACHI says that defrost on many systems ends when the coil reaches about 57°F, and that rapid cycling in and out of defrost is a sign of trouble. Rheem notes that newer electronic controls can go as long as six hours between defrosts when conditions allow, because they sense whether frost is really building rather than simply following a clock.

That last point explains why two neighbors can have different experiences. An older unit on a fixed timer may defrost on schedule even when little frost has formed. A newer demand-defrost unit defrosts only when it needs to. Neither is wrong. What you want is a pattern that is regular and ends on its own.

How long defrost lasts and how often it runs

A simple way to judge your own system

On a cold day, watch one defrost from start to finish. Note roughly when the outdoor fan stops and when it starts again. If the fan resumes within about 15 minutes and the house warms back up, the cycle did its job. If you see defrost repeating every few minutes, or it runs for much longer than 15 minutes, that is the point to schedule service.

Why a heat pump blows cool air or seems not to heat

This is the most common reason people search the topic. You walk past a vent in January and the air feels cool, so you assume the heat pump has quit. In defrost, the system is briefly in cooling mode, so the air coming from the vents is not as warm as usual, particularly if there is no electric backup heat to offset it.

A second reason is that heat pump air is naturally gentler than furnace air. A heat pump typically delivers air that feels warm but not hot, and a furnace blast can make it feel by comparison like the heat pump is blowing cold. If your home previously had a gas furnace, that difference can be a surprise. Our article on what causes HVAC to blow cold air when heating goes through the other common causes.

So how do you tell defrost from a real problem? Use the clock. If warm air returns within about 15 minutes, you saw defrost. If the air stays cool for an extended time, the thermostat does not show AUX heat, the outdoor unit is silent, or the cool air comes with ice on the unit, something else is going on. Common causes include thermostat settings, a tripped breaker, a failed control, low refrigerant, or a compressor problem. Those are jobs for a technician, and refrigerant work in particular must be done by a certified professional.

Why a heat pump blows cool air or seems not to heat

When frost or ice is a sign of a problem

Frost on the coil is normal. Ice that does not go away is not. Rheem’s owner’s manual draws the line clearly: the coil may be almost completely covered with frost at times and that is fine, but a thicker layer with hard, clear ice or new unusual noises means it is time to call a serviceman.

Trane says that ice which is not going away or is growing likely points to a bigger issue, such as low refrigerant, faulty defrost controls or a faulty sensor. Here is what each of those means in plain terms.

A faulty defrost sensor or control board. The sensor tells the board when the coil is cold enough to need defrost and when it has warmed enough to stop. If either part fails, the system may never defrost, or may defrost at the wrong times. American Standard notes that when the sensors or control board fail the ice will not melt, and a technician runs diagnostic tests to replace the faulty parts.

Low refrigerant. A leak lowers the system’s ability to move heat, which can cause the coil to ice and the heat to weaken. Signs include oily residue near the outdoor unit and a system that is running but not heating. Only a certified technician should work on a leaking system.

Blocked airflow or a failed fan. NACHI’s list of causes for an outdoor coil that fails to clear also includes a dirty coil covered with debris, a fan that will not turn, a bad reversing valve, wiring problems and a bad thermostat. It warns that without a working defrost cycle the coil can become a block of ice and damage can result.

The pattern to remember: a heat pump that is icing up for hours, defrosting constantly, or never defrosting at all needs attention soon, because ice can damage components. If you notice any of these, our heat pump repair team in Colorado Springs can diagnose which part is at fault. If the heat is out altogether during a cold snap, our guide to staying safe with a broken HVAC in winter covers how to keep the home safe until the repair is done.

What you can safely check yourself

There are a few checks that are safe and quick before you call. They are the same ones the manufacturers recommend.

Start with the thermostat. Confirm it is set to heat, the set temperature is above the room temperature, and the system is powered on. Check that the breaker has not tripped.

Next, look at the outdoor unit from a safe distance. If it has frost or ice, Trane recommends waiting a few hours to see whether it clears by itself, and calling an HVAC professional if the ice is not subsiding. Unusual noises are a reason to call right away.

Then clear what is around it. Snow drifts, leaves and mulch can restrict airflow and keep meltwater from draining. Rheem asks homeowners to keep snow cleared so defrost water can drain away and does not refreeze in the coil.

What not to do matters just as much. Do not chip or scrape ice off the coil or fins, which are thin and easy to damage. Do not pour hot water over the unit, and do not open the cabinet. Do not cover the unit either. Covering traps moisture and blocks the airflow the system needs, which is why we explain in our post on why heat pumps must stay uncovered in winter that a fall tune-up is the right preparation instead.

Preparing a heat pump for the heating season

Most defrost trouble starts before the first freeze. A coil clogged with dirt and pet hair holds more frost. A weak fan motor moves less air. A sensor that has drifted can trigger defrost at the wrong time. A fall tune-up looks at those parts while the weather is still mild, so the first cold week is not the first test.

A good fall visit generally covers the outdoor coil, fan, electrical connections, controls and refrigerant performance, and checks that defrost starts and ends as designed. We offer this as part of our HVAC maintenance plans and as a heat pump service call.

Year-round habits help too. Keep two feet of space around the outdoor unit, trim back plants, and direct roof runoff and downspouts away from the pad so water does not pool and freeze beneath the unit. In summer, reducing the heat load on the home helps the same equipment work less, and ideas like those in this piece on cooling a home without AC can take some pressure off the system on the hottest afternoons.

Is your heat pump the right one for Colorado Springs winters?

If your heat pump defrosts often or struggles on the coldest nights, it may be a matter of repair and tuning rather than replacement. If the system is older, has needed repeated defrost-related repairs, or was sized for a milder climate, an upgrade can make winter more comfortable. Modern variable and multi-stage units adjust output to conditions and hold a steadier indoor temperature.

Here are the heat pump packages we list, with the published starting prices from our pricing page:

System Starting price
15 SEER2 single-stage heat pump from $6,500
17 SEER2 three-stage heat pump from $8,500
18 SEER2 variable heat pump from $10,000

SEER2 is the efficiency rating for cooling, and a higher number means less electricity used for the same cooling. Exact pricing depends on your home, so the numbers above are starting points.

Fix it right with Strong Heating And Cooling

If your heat pump is icing, staying in defrost, or blowing cool air for longer than it should, we can find the cause and fix it. Our NATE-certified technicians work on heat pumps across Colorado Springs, we offer same-day service when needed, and our pricing is flat-rate with no hidden fees. If you are weighing a replacement, you can compare systems on our heat pump and AC pricing page.

Strongheatingandcooling

For repairs, start at our heat pump repair page, or see everything we handle for heating systems.

Our perspective on defrost

Most of the defrost calls that worry homeowners turn out to be a healthy system doing its job. Steam, a quiet fan and a little cool air for ten minutes are signs the heat pump is protecting itself. We would rather you understand that than lose sleep over it.

The calls that matter are the ones where the pattern changes. Ice that is thicker every morning, a unit that defrosts constantly, or heat that never quite returns. Those are the cases where a sensor, a control board, airflow or refrigerant needs to be looked at, and where waiting makes the repair bigger.

That is why we focus on doing the job correctly the first time and quoting it at a flat rate before we start. Colorado’s altitude and temperature swings put real demands on a heat pump, and a technician who works in this climate every winter knows what a normal cycle looks like here. Our NATE-certified team stands behind the work with a workmanship guarantee.

Owner

FAQ

How long should a heat pump stay in defrost mode?

Most defrost cycles last about 5 to 15 minutes. Some systems stop sooner once the coil reaches its target temperature, and many have a built-in maximum, such as 10 minutes on the Daikin units described above. If your unit stays in defrost much longer than 15 minutes, or heat does not return, schedule a service visit.

Why is my heat pump blowing cold air in winter?

If it lasts only a few minutes, the system is likely in defrost, and warm air should return when it ends. Heat pump air is also naturally cooler than furnace air, which can feel cold by comparison. If the air stays cool for a long time, check the thermostat and breaker, then call us to look at the controls, refrigerant and compressor.

Is it normal to see ice on my heat pump?

A light coating of frost is normal and clears during defrost. Thick, hard, clear ice that does not melt, or ice that grows from day to day, is not. Do not chip it off. Keep the area clear of snow, wait a few hours to see if it melts, and call a technician if it does not.

Can I force my heat pump into defrost mode?

We do not recommend it. Defrost is controlled by sensors and the control board, and forcing it can stress the system. If you think defrost is not starting, that is a sign the sensor or board needs diagnosing by a technician.

Sources

Need expert HVAC help?

Colorado Springs' veteran-owned heating & cooling team — Mon–Sat, 8 AM–7 PM. Same-day service when available.

800+

Furnace Installs

700+

Heat Pump Installs

550+

Air Conditioning Installs